TKZM-18脈沖控制儀TKZM-16,WD-1型溫度監測儀

一、       概述General

 “WD – 1型溫度監測儀”是用于監測溫度的智能化儀表。它通過對被監測系統的溫度監測，并參照您設定的報警值，對系統的工作狀況進行檢測、顯示與報警。

“WD-1 temperature monitor: is an inligent instrument which is used for monitoring the temperature. Through the temperature monitoring to monitored system and according to the alarm value set by you, this instrument can inspect, display and alarm the operation condition of system.

本儀表采用高性能的*處理器、傳感器、工業級IC模塊和高穩定性的元器件，并經過嚴格的老化與篩選。因此儀表具有穩定性好、精度高、抗*力強等特點。儀表殼體采用不銹鋼材料制成，適用于各種惡劣環境。

This instrument uses a central processing unit with high performance, sensor, IC module of industrial grade and components of high stability, and has passed strict aging and screening test. Therefore, this instrument is characterized by good stability, high precision and strong capacity of resisting disturbance. The instrument housing is made of stainless materials and is suitable for a variety of harsh environments.

二、主要功能說明II. Description of main functions

2.1     溫度監測  Temperature monitoring

本系統監測、顯示被監測系統的溫度（如循環水的溫度、油溫等），當溫度超過您設置的zui高溫度值和低于您設置的zui低溫度值時，系統進行報警。

The system monitors and displays the temperature (such as temperature of circulating water, oil temperature, etc.) of the monitored system. When the temperature exceeds the maximum temperature value and lower than the minimum temperature value set that you set, the system will alarm.

2.2     TKZM-18脈沖控制儀TKZM-16,WD-1型溫度監測儀報警   Alarm

系統報警后，可通過儀表輸出的DC24V/1A/1Hz的報警電信號驅動外接報警器；同時，儀表面板上相應的狀態指示燈閃爍，說明報警原因。

After system alarming, the external warner can be driven through the alarm signal of DC24V/1A/1Hz output by the instrument. At the same time, relevant status indicator lamp on the instrument flashes, indicating the cause of the alarm.

三、儀表的主要技術參數Main technical parameters of instrument

3.1     當前溫度顯示范圍：                               0~200.0 ℃
Current temperature display range:             0~200.0 ℃

3.2     溫度上、下限設置范圍：                        0~199.9 ℃
Setting range of upper and lower limit of temperature:     0~199.9 ℃

3.3     溫度顯示分辨率：                                   0.1 ℃
Resolution of temperature display:             0.1 ℃

3.4     儀表工作電源：                                      DC24V  2A
Working power of instrument:                    DC24V  2A

3.5     儀表自耗功率：                                      ＜5W
Power consumption of instrument:              ＜5W

3.6     儀表工作環境溫度：                               - 30 ℃~+70 ℃
Working environment temperature of instrument:      - 30 ℃~+70 ℃

3.7     儀表工作相對濕度：                               15% ~ 95%  （25 ℃時）
Working relative humidity of instrument:    15% ~ 95% (for 25 ℃)

3.8     儀表絕緣電阻：                                      ＞50MΩ
Insulation resistance of instrument:             ＞50MΩ

3.9     儀表耐壓：                                             1000V  3分鐘
Pressure proof of instrument:                     1000V  3min.

四、儀表使用說明Instrument instructions

概述 General
 

圖一是二次表面板示意圖，它分為三個部分。

Figure 1 is diagram for secondary instrument panel, which is divided into three parts.

*部分是數字顯示部分，顯示溫度數字量。本顯示部分采用液晶顯示器件，并帶自控背光源，無論環境光線強弱，顯示都一目了然。

The first part is digit display, displaying the temperature digit. The display uses LED components with self-control backlight; whether the ambient light is strong or weak, the display is clear.

第二部分是被監測系統溫度狀態指示燈。其中高溫、低溫指示燈是報警及原因指示。在參數設置時，又是設置相應報警值的指示。

The second part is the indicating light of temperature state of monitored system. In which, the high temperature and low temperature indicating lights are alarm and reason indication. In parameter settings, it is indications to set corresponding alarm value.

第三部分是儀表按鍵。它包括移位，調整兩個功能鍵。其具體功能見操作說明。

The third part is instrument presses, including two functional keys: replacement key and adjustment key. See instructions for their specific functions.

4.2     基本操作Basic operations

儀表通電后自動進入工作狀態。

After power on, the instrument automatically enter operating state.

使用儀表，必須通過儀表背板上的按鍵對相關報警值進行設置，否則，將使用出廠設置值。

When using the instrument for the first time, set corresponding alarm value by the presses on the instrument backboard, otherwise, the factory default settings shall be used.

附：指示燈在報警值設置時的定義與出廠時設置值：

Note: The definition of indicating light at the setting of alarm value and the factory-set value:

高溫——設置高溫報警值       出廠設置值：125.0℃

High temperature –Set high temperature alarm value  Factory-set value: 125.0℃

低溫——設置低溫報警值       出廠設置值：10.0℃

Low temperature –Set low temperature alarm value    Factory-set value: 10.0℃

4.2.1       設置高低溫報警值Set high and low temperature alarm value

在開機狀態下，同時按儀表背板上的移位、調整鍵，進入高、低溫報警值設置：

In the state of starting up, press the replacement key and adjustment key on the instrument backboard at the same time to enter the setting of high and low temperature alarm value:

進入設置狀態后，先設置的對象為高溫報警值，此時高溫狀態指示燈亮(如圖二所示)，相應數字顯示屏的數位數字閃爍（數字顯示屏所顯示的數值為系統上次設定值，例125.0℃）。按調整鍵循環選擇數的大小，正確后按移位鍵進入下一位數字設置。

After entering the setting state, the first set object is high temperature alarm value, at this point, the indicating light of high temperature state is on (see Figure 2), and the corresponding digital numbers on the digital display flashes (the number displayed on the digital display is the setting value for the last time, e.g. 125.0℃). Press the adjustment key to select the numbers cycled, when it is right, press replacement key to enter the setting of next digit.