1.Download:
【Software】 【64Driver】 【Manual】 【Firmware】 【SDK】
2.Accessories:
| |
| |
| |
| |
| |
3.Other Pictures
Connected to the computer can be used as a virtual oscilloscope | |
| |
| |
| |
| |
| |
| |
| |
4. Characteristic(Handheld Oscilloscope/Multimeter)
• 全隔離手持示波表,示波器通道間*隔離,示波器和萬用表通道隔離,示波器、萬用表與USB等通訊接口之間*隔離,隔離等級:1000V CATII,600V CATIII.
• High Bandwidth 60MHz-200MHz Oscilloscope,1GS/s sample rate, and 6000 Counts DMM with analog bargraph , and data recorder.
•
• High Refresh Rate (2500 frames)
• Large 5.6 inch TFT Color LCD Display,High Resolution(640*480), Dual-Window Design --More clear, More Detailed
• One-touch automatic setup optimizes the position, range, timebase, and triggering to assure a stable display of virtually any waveform
• Easy-to-use pop-up menu with built-in multi-language help system
• 23 Automatic Measurements
• Waveform Math: Add, Subtract, Multiply, and Divide
• Store and recall over
• Automatic cursor tracking measurements
• XY Mode
• Built-in FFT function converts a time-domain signal into its frequency components to measure harmonic content and distortion in systems
• Waveform Recorder to capture/replay input waveforms from CH1 and CH2 with a maximum record length of 1000 frames
• Pass-Fail function compares a stored waveform to an unknown input
• Average Mode for smoothing waveforms
• Square Wave Output (2V, 1kHz) for probe adjustment
• USB Host/Device 2.0 full-speed interface ,support removeable disk, LAN Optional ,Easy to control by PC or long-distance.
• Dimensions (mm):240(L)x165(W)x50(H), be carried easily.
• Labview\VB\VC Second Design instance.
5. Hardware Specification
Model | DSO1202S | DSO1122S | DSO1062S |
Oscilloscope mode | |||
Bandwidth | 200MHz | 120MHz | 60MHz |
Real-time Sample Rate | 1GSa/s | ||
Equivalent Sample Rate | 25GSa/s | ||
SEC/DIV Range | 2nS/div-2000S/div (in a 2, 4, 8 sequence) | ||
Delay Time Accuracy | 500ps | ||
Vertical | |||
A/D Converter | 8-bit resolution | ||
VOLTS/DIV Range | 2mV/div~5V/div at input BNC | ||
| ±50V(5V/div),±40V(2V/div~500mV/div), ±2V(200mV/div~50mV/div)±400mV(20mV/div~2mV/div) | ||
Record Length | Single-channel: Maximum | ||
Trigger | |||
Trigger Sensitivity | DC: CH1/CH2(Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full | ||
| CH1,CH2: ±8 divisions from center of screen | ||
Trigger Level Accuracy, | CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen) | ||
| 100ns-10s | ||
Trigger Type | |||
Edge | Trigger on the rising or falling edge | ||
Pulse Width | Trigger (when >,<,=,≠) on positive or negative pulses | ||
Video | Trigger on an NTSC, PAL, or SECAM standard video signal | ||
Slope | Trigger (when >,<,=,≠) on a positive or negative slope | ||
Overtime | from the rising or falling edge | ||
Alternate | Internal trigger on edge, pulse width, video or slope | ||
Measurement | |||
Cursors | Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz. | ||
Automatic | Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width | ||
Meter Mode | |||
Max.Resolution | 6,000 Counts | ||
DMM Testing Modes | Voltage, Current, Resistance, Capacitance,Diode & Continuity | ||
Max. Input Voltage | AC: 600V, DC: 800V | ||
Max. Input Current | AC: | ||
Input Impedance | 10 MΩ | ||
Isolation | |||
The float voltage between BNC and Ground | 600V CATIII, 1000V CAT II | ||
The float voltage between each Channel | 600V CATIII, 1000V CAT II | ||
The float voltage between Multimeter and Ground | 1000V | ||
between input Ports directly | 400V CAT II | ||
Input by 10:1 probe | 600V CATIII, 1000V CAT II | ||
The Max input voltage of Multimeter | DC 800V,AC 600V | ||
Display | |||
Type | Right angle 5.6 16-digit color LCD | ||
Resolution | 640*480 dots | ||
Contrast | 16 gears, with the progress bar to show adjustment | ||
Interface | USB host and USB slave, Lan Optional | ||
Power Supply | |||
Voltage | DC Input:12--17VDC, 2000mA | ||
Mechanical | |||
Size | 245 x 163 x 52 (mm) | ||
Weight | |
6.Software:
Operating system: Windows NT, Windows 2000, Windows XP ,
7.SecondDesign:
Supply DEMO code (VC、VB、LABVIEW)